Casting

Lost Foam Casting

Lost-foam casting (LFC) is a type of evaporative-pattern casting process that is similar to invest-ment casting except foam is used for the pattern instead of wax. This process takes advantage of the low boiling point of foam to simplify the investment casting process by removing the need to melt the wax out of the mold. First, a pattern is made from polystyrene foam, which can be done by many different ways. For small volume runs the pattern can be hand cut or machined from a solid block of foam; if the geometry is simple enough it can even be cut using a hot-wire foam cutter. If the volume is large, then the pattern can be mass-produced by a process similar to injec-tion molding. Pre-expanded beads of polystyrene are injected into a preheated aluminum mold at low pressure. Steam is then applied to the polystyrene which causes it to expand more to fill the die. The final pattern is approximately 97.5% air and 2.5% polystyrene. Pre-made pouring basins, runners, and risers can be hot glued to the pattern to finish it. Next, the foam cluster is coated with ceramic investment, also known as the refractory coating, via dipping, brushing, spraying or flow coating. This coating creates a barrier between the smooth foam surface and the coarse sand surface. Secondly it controls permeability, which allows the gas created by the vapor-ized foam pattern to escape through the coating and into the sand. Controlling permeability is a crucial step to avoid sand erosion. Finally, it forms a barrier so that molten metal does not pene-trate or cause sand erosion during pouring. After the coating dries, the cluster is placed into a flask and backed up with un-bonded sand. The sand is then compacted using a vibration table. Once compacted, the mold is ready to be poured. Automatic pouring is commonly used in LFC, as the pouring process is significantly more critical than in conventional foundry practice. There is no bake-out phase, as for lost-wax. The melt is poured directly into the foam-filled mold, burning out the foam as it pours. As the foam is of low density, the waste gas produced by this is relative-ly small and can escape through mold permeability, as for the usual outgassing control.

The strength of Haizol for Lost Foam Casting
We are partnering with the best supplier in the latest Lost Foam Casting processes with proprie-tary technology to deliver high quality, low cost custom made machined components from Asia. The whole ordering process is transparent and you will get update of your order with our Order Monitoring System.

COMPANY



LEGAL
CAPABILITY
 
CONTACT US
HAIZOL USA
500 South Kraemer Blvd., Suite 210,
Brea, California 92821
Phone: +1-657.258.9000
Email: info@haizol.com
HAIZOL China (Shanghai)
3/F, Building A4, No.1528 Gumei Road,
Xuhui District, Shanghai, China 200040
Phone: +86-21-3418.1600
Fax: +86-21-3418.1100
HAIZOL China (Guangdong)
405/409, Fortune Tower, 6093 Baoan Avenue,
Fuyong Street, Baoan District,
Shenzhen City, GuangDong Province, China
Phone: +86-0755-3394.7099
HAIZOL China (Jiangsu)
Room E1088, Nano Science Park,
Ruoshui Road 388, Suzhou Industrial Park,
Suzhou City, JiangSu Province, China
Phone: +86-0512-8783.1579
HAIZOL China (Zhejiang)
Room 1206B, Huamao First Headquarters,
555 Relizhong Road, Yinzhou District,
Ningbo City, ZheJiang Province, China
Phone: +86-0574-2761.4736
HAIZOL © 2015-2018
HAIZOL is A Registered Trademark © of Shanghai Hai Zhi Online Network Technology Co., Ltd. Record / License No.: Shanghai ICP 15049257.